Speed Queen Washer Error Codes Explained

Speed Queen washer error codes are designed to help owners and technicians quickly identify underlying issues, making it easier to resolve them. If you’re currently experiencing an error code with your Speed Queen washer, this guide will explain its meaning and provide steps to clear it.

Some Speed Queen error codes can be resolved with simple steps you can perform yourself. However, others may require professional assistance, especially if faulty components need to be replaced.

Error Codes for Speed Queen Washers

Below are some common error codes you might encounter on a Speed Queen washer.

ALrn, ALrn, or ALArn

These error codes indicate a Break-in Alarm Error. This occurs when there is an issue with the door or coin vault switches. Inspect and test these switches for proper functionality and address any faults.

E dF or E:dF

These error codes indicate a Drive Failure. Possible causes include an unplugged motor, motor failure, an open tachometer circuit, or a locked drum. To resolve this, unplug the machine to reset it and inspect the motor and drum for issues.

E dL or E:dL

These error codes indicate a Door Lock Error. It means the door failed to lock within 15 seconds of closing or didn’t unlock within 3 minutes after the cycle finished. To resolve the issue, securely open and close the door or check for any laundry items obstructing it.

E dL or Er, dL

These error codes indicate a Door Lock Fatal Error, meaning the door unlocked during a cycle. To resolve it, reset the machine. If the error persists, inspect the door lock, latch, and wire harness for damage or disconnection, and replace any faulty components.

E dL1 or Er, dl

These error codes indicate a Door Lock Non-Fatal Error. This occurs if the door fails to lock within 20 seconds of closing the door. To resolve it, try the following:

1. Ensure the door is fully closed.
2. Check for overloading or broken shocks that may prevent proper door closure.
3. Inspect the door lock and latch for damage.
4. Examine the door lock wire harness for disconnection or damage.

E dr

This error code indicates a Drain Alarm Error, meaning the machine has failed to drain. To resolve this issue, power down the machine and inspect the drain system. Check the drain hose for kinks or blockages, ensure the drain hose is installed at the proper height, and examine the drain pump filter for any obstructions.

E FL, E:FL or Er, FL

These error codes indicate a Fill Error. This occurs when the pressure switch does not open within the expected time during a fill cycle. To resolve this, check for:

• Adequate water pressure at the inlets.
• Proper operation of water valves.
• Clogs in the water line or hose filter screen.
• Air leaks in the pressure sensor hose.

E Ht, E:HT or E:Ht

These error codes indicate a Heater Error. The programmed temperature wasn’t reached within two hours, so the cycle will continue without the heater. To resolve this, replace any faulty heater circuit components.

E oP

This error code indicates an Open Thermistor Error, meaning the thermistor circuit opened during heating. As a result, the heater turns off, but the cycle will continue. Inspect and replace the thermistor if necessary.

E rr

This error code indicates a Coin Error, caused by incorrect coins being inserted or a malfunctioning coin sensor. Check the coin drop area for obstructions and clear them. If the issue persists, it could be due to tampering—review and strengthen security measures.

E SP

This error code indicates an SPI Communications Error, where the master control cannot communicate with the motor control. This is often caused by an unplugged transformer or incorrect wiring to the motor control. To resolve this, power down the machine, check connections, and power it back up.

E Ub or E:Ub

This error code means the washer cannot balance the load. To resolve this, redistribute the load evenly and restart the cycle.

E nr or Er, nr

This error code indicates a Drive Board Not Ready error, caused by a hardware failure. To resolve this, reset the washer. If the error persists, the drive board may need to be replaced.

E SH or Er, SH

This error code indicates a shorted temperature/thermistor sensor. It occurs when the drive board detects a temperature above 100°C (212°F). The heater is turned off for the rest of the cycle, and the error clears after one minute or a key press. Check the wiring to the heating elements and thermistor for damage or faults.

E SudS or Er, SL

This error code indicates a Suds Lock Error, meaning excessive suds were detected even after running all programmed Suds Removal Routines. To resolve this:

• Use less detergent to prevent excess suds.
• Check for drainage issues.
• Ensure the drum spins freely and no small items are stuck between the drum and the outer tub.

E Hd or Er, Hd

This error code indicates the water is too hot to drain safely, possibly because of a stuck heater relay. Inspect the heater relay for proper function, and replace it if it is stuck or defective.

E Ld or Er, LE

This error code indicates a Water Leak Drain Error. It occurs if water leaks during the cycle, causing the water level to drop below acceptable levels. To resolve this, check for a leaking drain hose or a stuck gravity drain valve and repair or replace the faulty component as needed.

E oF or Er, OF

These error codes indicate an Overflow Error caused by an unsafely high water level that cannot drain. To resolve this, check for a stuck-open water valve, a clogged drain, or a pump impeller obstruction.

Summary

This is not an exhaustive list of all error codes for Speed Queen washers, but it includes many of the most common ones. Some issues can be resolved on your own, while others may require professional assistance. Don’t hesitate to reach out to a professional if needed.

In some cases, resetting the appliance can resolve error codes caused by temporary control glitches. To reset your Speed Queen washer, unplug it, wait for three minutes, and then plug it back in.